To create a low cost servo solution, the SV is offered with the new V series servo motors. Learn more…
POWER SUPPLY:
|
PROTECTION:
|
S - models
Q - models
Si - models
Analog Inputs:
Analog inputs for analog speed and positioning modes - Configurable 0-10V, 0-5V, ±10V or ±5V, with or without offset
Outputs:
Four digital outputs
Optional:
RS-485 multi-drop communication
Encoder outputs to motion controller
AMPLIFIER TYPE | Digital MOSFET. 16 kHz PWM |
CURRENT CONTROL | DSP Software current control using D-Q method |
OUTPUT TORQUE | 0.5 to 7.0 amps rms continuous, 0.5 to 14 amps rms peak (2 seconds max, i2t limiting) |
POWER SUPPLY | External 18 — 88 VDC — Power Supply Required |
PROTECTION | Over-Voltage, Under-Voltage, Over-Temp, Motor/wiring shorts (Phase-to-Phase, Phase-to-Ground) |
IDLE CURRENT REDUCTION | Reduction range of 0 – 90% of Running Current after delay selectable in milliseconds |
AMBIENT TEMPERATURE | 0 to 40°C (32 - 104°F) (SV7 must be mounted to suitable heatsink) |
HUMIDITY | 90% non-condensing |
NON-VOLATILE STORAGE | Programs, Data and drive configuration are saved in FLASH and EEPROM memory - Adjustable Digital Filter |
MODE OF OPERATION | Step & Direction, CW/CCW, A/B Quadrature, Oscillator, Joystick, SCL, Hub |
INPUTS |
X1, X2 Optically isolated, differential, 5 Volt. Minimum pulse width = 250 ns. Maximum pulse frequency = 2 MHz, X3 Optically isolated, 12 - 24V, sourcing or sinking, X4 Optically isolated, 12 - 24V, sourcing or sinking, X5, X6 Optically isolated, 12 - 24V, sourcing or sinking, X7, X8 Optically isolated, differential, 12 - 24V, |
OUTPUTS |
Y1 Optical darlington, 30V, 100mA max, NPN/sinking, Y2 Optical darlington, 30V, 100mA max, NPN/sinking, Y3 Optical darlington, 30V, 100mA max, NPN/sinking, Y4 Optical darlington, 30V, 100mA max, configurable as sinking or sourcing, |
TWO ANALOG INPUTS | Range: ±10V Resolution: 12 bits (with ±10V signal range) 100 kOhms internal impedance |
COMMUNICATION INTERFACE | RS-232 standard, optional RS-485 |
AGENCY APPROVALS | RoHS CE EN 61800-3: 2004 EN 61800-5-1: 2003 |
Q Programmer™ – Create Single-Axis Motion Control Programs for Q and Plus Drives
Q Programmer is used to create and edit stand-alone programs for Q version drives. The functions of these drives include multi-tasking, math, register manipulation, encoder following, and more.
System Requirements: Microsoft Windows 10, 8, 7, Vista or XP, 32-bit or 64-bit.
Si Programmer™ – Create Stand-Alone Indexing Programs for i and Si Drives
Intended for use in stand-alone applications, Si Programmer provides a user friendly, point-and-click, graphical interface that doesn’t require any previous programming experience.
System Requirements: Microsoft Windows 10, 7, Vista, XP, NT, 2000, ME or 98, 32-bit or 64-bit.
Quick Tuner™ – Tune and Configure Servo Drives
Used for setup, configuration of the drive. Learn more…
System Requirements: Microsoft Windows 10, 8, 7, Vista or XP, 32-bit or 64-bit.